TH2810D Digital Inductance Meter TH2811D
- Popis
- Poptávka
Popis
Inductance Meter
Funkce
100Hz,120Hz,1kHz,10kHz 4 typical test frequencies
4.3 inch TFT liquid crystal display, Čínština a angličtina
optional operation interface
6-digit reading resolution
Maximum test speed:12.5slečna, support low frequency and high
Rychlost:TX4+3ms
10 bins sorting, test sorting is more perfect
100 sets of LCRZ instrument setting files, 10 měření
Soft power switch
Support 110V/220V two power supply voltages
10-point list sweep, support multi-frequency test sorting
Ultra-low signal source output offset (<100μV), meeting the
needs of large inductor, common mode choke inductor test
Super impact protection
Power on state lock button;
Empty fixture judgment
Data logging function
Screen capture function
Interface function, timing, trigger delay, atd. are more complete
Inductance Meter
Technický parametr
| Modelka | TH2810B+ |
| Základní přesnost | 0.1% |
| Testovací frekvence | 100Hz,120Hz,1kHz,10kHz |
| Test Parameters | L, C, R,Z|, D, Q, X, d, thr, Vm, Im, % |
| V/I Monitor | Ano |
| AC Test Signal Level | 0.1Vrms,0.3Vrms,1Vrms |
| Signal Source Internal Resistance | 10Ach, 100Ach |
| Test Terminal Configuration | 5-terminal |
| Test rychlosti(ms/time) | Rychle: 19slečna; Střední:83slečna; Pomalý: 333msF≤120Hz Fast :4XT+3ms |
| Zero Clearing | OTEVŘENO, Short, Load |
| List Sweep | 10-point list sweep; Each scan point can be individually sorted, support multi-frequency combined test sorting; Scanning test for frequency and AC voltage |
| EquivalentCircuit | Série, Paralelní |
| Range Mode | AUTO, HOLD |
| Režim spouštění | Vnitřní, Externí, Manuál, Bus |
| Average Times | 1-255 |
| Arithmetical Operation | Přímé čtení, břišní svaly,% |
| Delay | Trigger delay, step delay: 0—60.000s, 1ms step |
| General Function | Série, parallel equivalent mode, calibration: otevřený obvod, zkrat, range selection: automatický, manuál, trigger mode: INT, MUŽ,EXT, AUTOBUS, keyboard lock function |
| Komparátor | 10 bins sorting,BIN1-BIN9,NG,AUX; Bin count function PASS, FALL front panel LED display |
| Nonvolatile Storage | 100 sets of LCRZ instrument setting files, 10 test results |
| External USB Storage | Instrument setting file, CSV data file |
| Modelka | TH2810D | TH2811D |
| Measurement Function | ||
| Testovací parametr | L-Q, C-D, R-Q,Z|-Q | |
| Základní přesnost | 0.1% | 0.2% |
| Equivalents Circuit | Série, paralelní | |
| Mathematical Functions | Deviation and PercentDeviation | —— |
| Rang Mode | Auto, Držet | |
| Režim spouštění | Vnitřní, Manual andExternal | Vnitřní |
| Rychlost měření | Rychle: 12, S: 5.1, Pomalý: 2.5 (meas/ sec) | |
| Correction Function | Open/Short multi-frequency Zeroing | |
| Measurement Terminals | Five Terminals | |
| Test Signal | ||
| Testovací frekvence | 100Hz,120Hz,1kHz,10kHz,Přesnost 0.01% | |
| Operation Temperature & Vlhkost vzduchu | 0°C – 40°C, ≤ 90 % RH | |
| Power Requirements | Napětí | 99PROTI – 121PROTI, 198PROTI – 242PROTI |
| Frekvence | 47.5Hz – 63Hz | |
| Spotřeba energie | ≤20 VA | |
| Rozměry (Š×V×H) | 270mmx130mmx300mm | |
| Hmotnost | Cca. 3.7kg | |
